The Harbour Gallery has relocated from St Aubin to 19 The Quay, Commercial Buildings in St Helier, Jersey. It is beside the St Helier Old Harbour.
Open seven days a week, 9:30am – 5:30pm. The gallery features the work of over 100 local artists and craftworkers spread over three floors.
Please note that the Harbour Gallery is temporarily closed ready to relocate from St Aubin to St Helier.
The Gallery’s new address will be 19 The Quay, Commercial Buildings, St Helier, JE1 1BU.
The planned opening date is February 2023.
Selected products from St Aubin Studio are now available on the “Made in Jersey” website. This website is a collection of some of the best artists in Jersey and can be viewed here.
Don’t forget that the full St Aubin Collection is always available here, at StAubinStudio.com.
Please remember that handcrafted masks are not a substitute for PPE in health care settings.
Presented here are a some options and variants for sewing fabric masks.
Pattern and instructions available as a PDF document from here
2 pieces of 6” x 9” 100% cotton fabric of varying colors
1 piece of 6” x 9” cotton fabric lining or light weight interfacing for lining
2 pieces of 1/8” x 7” elastic OR Fabric Ties - Cut 4 strips of fabric 1-1/2” x 18”
Sewing machine
Scissors or a trimmer
Pins or clips
Pencil or Hera marker
Thread
Iron
ALTERNATE SIZING: (Use the same size fabric ties for all sizes)
Adult Male: Fabric 7” x 9” with 1/8” x 7” elastic straps
Adult Female: Fabric 6” x 9” with 1/8” x 6” elastic straps
Children: Fabric 5” x 7” with 1.8” x 5.5” elastic straps
Remember, handcrafted masks are not a substitute for PPE in health care settings. here are some interesting articles regarding face masks from the CDC (USA Centers for Disease Control and Prevention).
How to make a mask with elastic straps:
How to make a mask with fabric ties:
This site (HappyDIYHome.com) has instructions and clear photos for making five different types of fabric masks.
A JustGiving page has been setup by Bella Ward to urgently raise funds for medical PPE (personal protective equipment) for our Jersey care homes and essential workers NOT receiving States (Government) or Parish funds in the COVID-19 crisis.
Anything you can donate is gratefully received. Please donate here.
This information is being shared to make it easier to spread the message and as a result, have more (much needed) masks made. The content here is from Erica Made Design LLC and we thank Erica Made Design LLC for allowing this to be shared. Stay safe everyone.
Please remember that handcrafted masks are not a substitute for PPE in health care settings.
If you are a Cricut cutting machine user, then you will love these patterns shared by Cricut. There are instructions with each pattern.
Simplified face mask pattern: Adult large / Adult small/medium / Youth regular / Youth small
Face mask with filter pattern: Adult large / Adult small/medium / Youth regular / Youth small
Remember, handcrafted masks are not a substitute for PPE in health care settings. here are some interesting articles regarding face masks from the CDC (USA Centers for Disease Control and Prevention).
A JustGiving page has been setup by Bella Ward to urgently raise funds for medical PPE (personal protective equipment) for our Jersey care homes and essential workers NOT receiving States (Government) or Parish funds in the COVID-19 crisis.
Anything you can donate is gratefully received. Please donate here.
This information is being shared to make it easier to spread the message and as a result, have more (much needed) masks made. The content here is from Erica Made Design LLC and we thank Erica Made Design LLC for allowing this to be shared. Stay safe everyone.
CLEAR Florist cellophane/wrap. The more microns the better, the thicker the better
Cut into 300mm x 400mm, use 2 layers (3 if thin)
If your cellophane is 800 wide then you can just fold it over
Bias Binding
Clear document folders
Cut the document folders cut strips:
2 cm strip for the headband
1 cm strip for the bottom to weight it and hold it in place
Using 1m (metre) of Bias binding or tape:
Fold the bias binding in two and mark the middle
From the middle mark 117mm either side (bias binding is slightly stretchy so Stretch it out before you measure it to get rid of the stretch).
Attach the 2 cm piece of document folder 3 cm from the top (it helps to peg at either end to hold it in place).
Attach the 1 cm strip of document folder at the bottom.
Cut off the corners at the bottom to allow movement.
Now attach the bias binding or tape at your marked pieces to either end of the top leaving the mask bowing slightly. This will keep it away from the face especially if you wear glasses and stop it steaming up!
A JustGiving page has been setup by Bella Ward to urgently raise funds for medical PPE (personal protective equipment) for our Jersey care homes and essential workers NOT receiving States (Government) or Parish funds in the COVID-19 crisis.
Anything you can donate is gratefully received. Please donate here.
This information is being shared to make it easier to spread the message and as a result, have more (much needed) masks made. The content here is from Steve and Amanda Frost and we thank Steve and Amanda
Frost for allowing this to be shared. Stay safe everyone.
3D printing files (these can be found here). Please note the advice for making these safely.
3D printer
3D printed upper part - headband (1 of)
3D printed lower part - chin (1 of)
Elastic band - classic or buttonhole, length 33 cm (1 of)
Laminating film - glued in heated roll, size A4, thickness 0.5 - 1.0 mm (1 of)
Hole punch (1 of) designed for 2 hole puncher with a spacing of 80 mm
Marker (1 of)
Anyone with a 3D printer who wishes to get involved should contact Max Livesey (maxlivesey@googlemail.com) or Ken Hudson.
Bailiwick Express - 3D printing pros unite to help health staff - 01 April 2020
Jersey Evening Post - Engineer uses 3D print skills to convert masks - 14 April 2020
If you are looking for help or support with your 3D printing of face shields, try these Facebook groups:
A JustGiving page has been setup by Bella Ward to urgently raise funds medical PPE (personal protective equipment) for our Jersey care homes and essential workers NOT receiving States (Government) or Parish funds in the COVID-19 crisis.
Anything you can donate is gratefully received. Please donate here.
This information is being shared to make it easier to spread the message and as a result, have more (much needed) masks made. The content here is from Prusa Research and we thank Prusa Research for allowing this to be shared. Stay safe everyone.
From 30 March 2020, To coincide with the Harbour Gallery temporarily closing and the Jersey “lockdown” caused by the Covid-19 virus, all orders within the island of Jersey CI will be free.
Orders will either be delivered by Jersey Post or personally delivered.
To purchase, navigate to the item you like and click on “Add to Basket”. Note that some items have different options for you to select from.
Stay safe.
